Differences
This shows you the differences between two versions of the page.
| Both sides previous revision Previous revision | |||
|
en:activer_un_ecran_sony_android_dans_signage [2025/09/26 17:23] admin removed |
— (current) | ||
|---|---|---|---|
| Line 1: | Line 1: | ||
| - | ====== Activate a Sony Android Screen in Signage ====== | ||
| - | |||
| - | ===== Step 0: Before Provisioning the Screen ===== | ||
| - | |||
| - | Check that the screen is properly connected to the internet | ||
| - | |||
| - | Check the firmware version: | ||
| - | |||
| - | Press the Help button on the remote, then go to System information | ||
| - | |||
| - | Note the following information: | ||
| - | |||
| - | The serial number | ||
| - | |||
| - | The screen ID | ||
| - | |||
| - | The screen model | ||
| - | |||
| - | Check the Software version, the package version must be at least PKG6.7532 | ||
| - | |||
| - | Retrieve the MAC Address: Press the HELP button on the remote, then go to Network status and diagnostics, where you can find the MAC Address. | ||
| - | |||
| - | <WRAP round important 30%>If the package version is lower than 6.7532 | ||
| - | |||
| - | Press the “Help” button on the remote | ||
| - | |||
| - | Go to “System software update” | ||
| - | |||
| - | Click on “Software update” Let the screen perform the update, restart if necessary.</WRAP> | ||
| - | |||
| - | ===== Step 1: Register the Screen in the RDM ===== | ||
| - | |||
| - | Go to https://apps.rdm.sony.net | ||
| - | |||
| - | Register the screen: {{ :fr:sonyrdm.png?1000 |}} Choose the profile corresponding to the model | ||
| - | |||
| - | ===== Step 2: Factory Data Reset ===== | ||
| - | |||
| - | Go to Settings > System > About > Reset | ||
| - | |||
| - | Click on Factory Data Reset The screen will restart. | ||
| - | |||
| - | <WRAP round important 30%>During the restart, the Sony screen will display a dropdown list to choose the language. Do not take any action and wait.</WRAP> | ||
| - | |||
| - | ===== Step 3: Provision the Screen in the RDM ===== | ||
| - | |||
| - | Go to the Provisioning section | ||
| - | |||
| - | Enter the code displayed on the screen {{ :fr:sonyrdm2.png?1000 |}} The screen will provision on Sony’s RDM. | ||
| - | |||
| - | ===== Step 4: Update the Android Webview ===== | ||
| - | |||
| - | Exit Pro mode via the remote by pressing sequentially: i+ / mute / volume+ / home to enter “Pro settings” | ||
| - | |||
| - | The screen should display a banner indicating that it is in the “Pro settings in process” state. | ||
| - | |||
| - | Enable developer mode on the screen: | ||
| - | |||
| - | Go to Settings > System > About | ||
| - | |||
| - | Click on Android TV OS build (5 times) | ||
| - | |||
| - | Go to Settings > Developer options | ||
| - | |||
| - | Enable ADB debugging | ||
| - | |||
| - | ==== Webview Update: ==== | ||
| - | |||
| - | Download the installation zip | ||
| - | |||
| - | Run the following commands according to your operating system | ||
| - | |||
| - | Run PowerShell as Administrator (required for ADB). | ||
| - | |||
| - | Enable script execution if necessary with the following command: Set-ExecutionPolicy Unrestricted -Scope Process | ||
| - | |||
| - | Run the script with the device’s IP: .\install_zebrix_sony.ps1 <ip_address> | ||
| - | |||
| - | (First, look up the IP in the screen's network settings) | ||
| - | |||
| - | === Exit "Pro settings" mode to enter "Pro" mode === | ||
| - | |||
| - | Go to Settings > Pro settings | ||
| - | |||
| - | Click on Start Pro mode | ||
